Tile in every home decoration is almost essential Many kinds, full-colour, quality varies, do not understand the consumer is often confused by the bad as good, substandard products, the market tile a high-quality tile some up to more than 1000 a piece, while some as low as 20 to 30. Home improvement will always use tiles, how do choose a cost-effective tile? Today, we take you to understand the knowledge of tile differentiation and its purchase.

Home tile selection guide - home improvement tile how to choose? 

1. product appearance

Consumers in the purchase of tiles from the box inside any sample check a few tiles and see the product surface has the following defects: lack of glaze, spots, cracks, bumps, glaze bubbles, peeling edge, ripples, etc. General from the porcelain 3m visual inspection, defects are not obvious and do not affect the use of qualified products. Each tile has a product trademark on the back, in the side and back also does not allow the adhesion of glaze and other obstacles to bonding affect the use of the obvious fall destroyed. Also pay attention to the tiles and the box on the identification and specifications, the colour number is consistent, product certification, trademark and quality inspection mark shallow is clear.

2. tile colour and colour difference

To check whether the tile blank colour is pure. This trick is very simple, the main observation of the back of the tile colour is uniform and consistent. Better quality tiles, the blank colour is uniform and uniform. To observe the tile cross-section of the grain is fine. Consumers should note that the cross-section referred to here does not refer to the cutting surface around the tile, but to the fracture of the tile break. As the number of tiles needed in the decoration is usually relatively large, if the tile has a significant colour difference, it will affect the decoration effect, so consumers in the purchase of tiles to all the packaging of the product sampling comparison, observe the change in colour difference, the colour difference can not be used.

3. look at the flatness of the tile surface

Many customers in preparation for the purchase of tiles, will make a point of asking about customer service flatness, reflecting the uneven tiles bought in the market; more customers do not know how to judge the flatness of the uneven tiles laid on only to find that had to buckle up and buy a new batch of tiles. In fact, the tile surface paved up uneven condition, there are two aspects, one is the decorator's craftsmanship is not good; second is the quality of the tile itself. In the tile has not been laid, it is recommended that we first look at the flatness of the tile surface, to confirm that there is no error, and then call the decorator to work, so as to avoid the problems caused by the tiles and aesthetic problems, but also to avoid the master of their craft problems shifted to the tile problem up.

4. sound discrimination

Lightly hit with a hard object, the crisper the sound, the higher the degree of porcelain, the better the quality. You can also be the left thumb, index finger and middle finger clip tile corner, easy to hang down, with the right index finger lightly hit the lower part of the tile, such as the sound is crisp, pleasant for the top, such as the sound dull, stagnant for the bottom.

5. tile wear resistance

Now the tile in the wear resistance of a series of innovations, whether polished tiles, microcrystalline stone, full glaze, antique tiles and so on, have a qualitative leap, then the initial judgment of the surface is wear-resistant, it is said that good cloth is not afraid of grinding to grind, good tile is able to accept the test of sharp instruments, pick up the sharp knife in hand, enjoy scraping to the surface of the tile, to see if the tile surface glaze layer will be scraped off, is powder or scratch This can determine how hard the tile if even such a small scratch can not withstand, it can be concluded that the tile is not a long time to use.

6. check the tile stain resistance

Tile will accompany us for a long period of life. If dirty is not easy to clean, it is estimated that in less than three or four years, even if you do not want to stay in a dirty home, I can not wait to put these tiles up and resurface. The tile surface antifouling agent is removed, and coated with different pollutants (odd pens, ink, etc.), after standing for 5 minutes, compare the ease of removing pollution the more convenient the better. Another comparison of pollution resistance durability, you can leave the dirt 1, 2 days after, compare the ease of removal and leave stain marks depth, the shallower the better anti-soiling.

7. pour water to verify the density

Water absorption reflects the density of the tile, and indirectly also reflects the hardness of the tile, but one thing to note, the tile is not the lower the water absorption rate is better. Here the water absorption rate test, is for the living room, bedroom, walkway and other areas of the tile do the test, just think, if the tiles in these places are sucked into the water, is not the whole area into the wet state? Without delay, we first pour the water to the front and back of the tile, and carefully observe the water infiltration, if you buy polished tiles, water is immediately sucked in, congratulations, encountered poor quality polished tiles.

8. corner straightness test

As mentioned in the previous step, the tile surface determines the effect of laying up flat, and tile corners straightness test, the purpose is to see whether the overall tile paving is neat, the gap size is consistent. At this time, we pick up a few tiles together on a flat surface and pay attention to observing whether the gaps between the tiles and tiles are consistent, whether the corners of the tiles can be put together and not too much rejection. If the corners are not regular straight, the tiles must be untidy, which affects the overall tiling effect.

9. weight

Through the weight of the tile to determine whether the tile is good or bad, good tile weight is larger, high density. Good tile weight is heavier, more solid, uniform in thickness, corners without warping and other defects, the weight of poor quality tiles is relatively light.

Buy tiles from the professional tiles online store hanseceramictile.com, with constant delivery and a safe deal!